Magnum THF 230P AC/DC

The MAGNUM THF 230P AC/DC is a professional inverter welder designed for manual electric TIG welding with AC and DC current. The device can also be used to weld using the MMA method with fusible covered electrodes. The MAGNUM THF 230P welder is powered from a single-phase 230V mains, has a high 60% duty cycle at 200 A. It is designed for all kinds of welding work in locksmith workshops, repair shops, industrial workshops, factories, etc. The unit is equipped with a large, clear soft control panel that allows you to set all the necessary welding functions (current: start/ crater fill/weld/base, current rise and fall time, gas discharge before and after welding, pulse frequency, balance, etc.). The current source is built on IGBT transistors to ensure minimum electromagnetic interference and low power loss, enabling increased efficiency and reliability of the current source. The very high efficiency, which directly translates into lower power consumption, and high switching frequency ensure instantaneous current adjustment to changes in parameters during welding. The digital function panel allows precise control and selection of all the most important welding parameters: . - TIG AC, TIG DC, MMA welding method selection - 2T/4T operation mode - TIG pulse: on/off - AC balance - AC current frequency - Gas discharge before welding - Initial current - Welding current rise time - Peak welding current value, when welding with TIG Puls method - Welding current value, when welding with MMA and TIG method - Frequency of welding current pulsation for TIG Puls method - Pulsation balance- ratio of peak current to base current for TIG Puls method - Descending time of welding current to final current value - Final current - Gas discharge time after welding PARAMETER ADJUSTMENT RANGE:. - gas before - gas outflow time before welding: 0.3 - 10 [s]. - Ip - initial current: 10-200 [A] - tn - rise time of Ip current to ls/b: 0 - 10 [s] - Imax - peak TIG pulse current: 10 - 200 [A]. - Is/b - TIG welding current, base TIG pulse current: 10 - 200 [A]. - pulse [Hz] - TIG current frequency pulse: 0.5 - 100 [Hz]. - pulse [%] - balance of currents (peak to base) TIG pulse: 1- 99 [%]. - to - current falling time Is/b to Ik: 0 - 10 [s]. - Ik - final current: 10- 200 [A] - gas after - time of gas discharge after welding: 1 - 30 [s] - AC frequency - frequency of polarity change: 50- 150 [Hz]. - AC balance [%] - polarity change balance: 20 - 50 [Hz]The MAGNUM THF 230P AC/DC is a professional inverter welder designed for manual electric TIG welding with AC and DC current. The device can also be used to weld using the MMA method with fusible covered electrodes. The MAGNUM THF 230P welder is powered from a single-phase 230V mains, has a high 60% duty cycle at 200 A. It is designed for all kinds of welding work in locksmith workshops, repair shops, industrial workshops, factories, etc. The unit is equipped with a large, clear soft control panel that allows you to set all the necessary welding functions (current: start/ crater fill/weld/base, current rise and fall time, gas discharge before and after welding, pulse frequency, balance, etc.). The current source is built on IGBT transistors to ensure minimum electromagnetic interference and low power loss, enabling increased efficiency and reliability of the current source. The very high efficiency, which directly translates into lower power consumption, and high switching frequency ensure instantaneous current adjustment to changes in parameters during welding. The digital function panel allows precise control and selection of all the most important welding parameters: . - TIG AC, TIG DC, MMA welding method selection - 2T/4T operation mode - TIG pulse: on/off - AC balance - AC current frequency - Gas discharge before welding - Initial current - Welding current rise time - Peak welding current value, when welding with TIG Puls method - Welding current value, when welding with MMA and TIG method - Frequency of welding current pulsation for TIG Puls method - Pulsation balance- ratio of peak current to base current for TIG Puls method - Descending time of welding current to final current value - Final current - Gas discharge time after welding PARAMETER ADJUSTMENT RANGE:. - gas before - gas outflow time before welding: 0.3 - 10 [s]. - Ip - initial current: 10-200 [A] - tn - rise time of Ip current to ls/b: 0 - 10 [s] - Imax - peak TIG pulse current: 10 - 200 [A]. - Is/b - TIG welding current, base TIG pulse current: 10 - 200 [A]. - pulse [Hz] - TIG current frequency pulse: 0.5 - 100 [Hz]. - pulse [%] - balance of currents (peak to base) TIG pulse: 1- 99 [%]. - to - current falling time Is/b to Ik: 0 - 10 [s]. - Ik - final current: 10- 200 [A] - gas after - time of gas discharge after welding: 1 - 30 [s] - AC frequency - frequency of polarity change: 50- 150 [Hz]. - AC balance [%] - polarity change balance: 20 - 50 [Hz] TECHNICAL DATA:- Power supply: AC 230 [V], 50/ [Hz], - Required protection: 25 [A] / C - Power consumption: 5.7 [kW]. - Efficiency: 60 [%]. - Idling voltage Uo: 68 [V] - TIG AC welding current: 10 - 200 [A]. - DC TIG welding current: 10 - 200 [A]. - MMA welding current: 10 - 200 [A] - Housing protection class: IP23 - Weight: 12.6 [kg]