MIGOMAT welder IDEAL TECNOMIG 201 MMA SYNERGY KIT.

Semi-automatic welding machine powered by single-phase IDEAL TECNOMIG 201 Synergia made with IGBT inverter technology for MIG/MAG (gas-shielded) or FLUX (non-gas-shielded) welding and welding with direct current (DC) covered electrodes. TECNOMIG 201 SYNERGIC is an inverter synergic semi-automatic welding machine designed for arc welding by MIG/MAG, TIG LIFT, MMA and FLUX methods. The machine has been designed for a wide range of applications: from maintenance work to auto body repair. It is designed for welding with welding wires with a diameter of 0.6-1.0 mm, 0.9 mm self-consuming wires and covered electrodes with a diameter of up to 4 mm of low-carbon steel, low-alloyed steel (MAG), alloyed steel (MIG), aluminum and cast iron. Semi-automatic welding machine powered by single-phase IDEAL TECNOMIG 201 Synergia made with IGBT inverter technology for MIG/MAG (gas-shielded) or FLUX (non-gas-shielded) welding and welding with direct current (DC) covered electrodes. TECNOMIG 201 SYNERGIC is an inverter synergic semi-automatic welding machine designed for arc welding by MIG/MAG, TIG LIFT, MMA and FLUX methods. The device has been invited for a wide range of applications: from maintenance work to auto body repair. It is designed for welding with welding wires of 0.6-1.0 mm diameter, 0.9 mm self-consuming wires and covered electrodes of up to 4 mm diameter of low-carbon steel, low-alloyed steel (MAG), alloyed steel (MIG), aluminum and cast iron. Max spool 5 kg D200. The IDEAL TECNOMIG 201 semi-automatic machine has: display of welding current parameters electronically controlled smooth adjustment of welding current electronically controlled infinitely variable adjustment of wire feed speed overload protection. Designed for workshop and field work. ONE OF THE MOST POPULAR HOME AND WORKSHOP EQUIPMENT ADVANTAGES OF THE DEVICE Built-in synergy programs for welding: steel, stainless and aluminum, soldering and FLUX Possibility of manual and synergic settings ! The device has 9 synergic programs for welding steel. Possibility of soldering The device is ready for welding Welding current 40-200A Inductance adjustment 2-takt 4-takt function SPOT WELDING FLUX welding Fan walking system Unit powered at 230V Possibility of using TIG LIFT handle Possibility of changing the polarity of the device Clear intuitive panel for the selection of welding parameters Robust metal FEEDER Small dimensions and high mobility of the device Clear and easy-to-use control panel allows selection of welding program TECNOMIG 201 is used for welding stainless steel, carbon and low alloy steels and aluminum . Welding is carried out under the cover of inert gas, active gas or mixture and in reverse polarity without gas. The device has 9 synergy programs for welding steel. Quick synergic adjustment of welding parameters through an easy-to-read control panel makes the device very easy to use. All you need to do is set the welding wire thickness and gas type and start welding: the intelligent and automatic welding arc control system will, step by step, select the best parameters, for each welding position and material. The user can also set the welding arc length manually and adjust the appearance of the weld to suit his needs. Inductance control - allows to reduce the amount of heat in the welding position. The sheet metal does not deform and the protective layer of tin is not damaged, a feature used in soldering. Higher inductance (soft arc) results in a wider welding pool and fewer spatters . In contrast, lower inductance produces a stable, focused arc. BUTOSWELDING - MIG/MAG brazing has adopted a name formed from two different technologies. Brazing as a welding process, in which there is no melting of the parent material only of the solder, and MIG/ MAG welding technology, from which the preparation of the edges of the material as for welding and the method of melting the wire in an electric arc in an atmosphere of protective gases, fed automatically from a spool, were used. Brazing could, therefore, be called welding brazing. The protective gas used is usually pure argon In the welding process, evaporating zinc is the cause of porosity in the welds, as the high temperatures generated in this area destroy the protective layer, the joined parts lose their corrosion resistance. Mechanical removal of zinc before welding as well as reapplication in places where evaporation has occurred is a very expensive process. Filling cavities with zinc preparations ( paints) insufficiently protects the structure from corrosion. In addition, it should be noted that when welding galvanized sheets, there is a very high emission of zinc fumes that are harmful to health. These inconveniences can be avoided by using MIG/ MAG brazing technology. The 2t double-buttons - pressing the button initiates the gas flow and welding current, pressing the button turns off the welding current, Four-bar 4t - pressing and releasing the handle button initiates gas discharge and welding current, pressing and releasing the button again turns off the welding current, IGBT - modern transistors are used in the welder, a solution that provides a minimum of electromagnetic interference low power loss in the basic circuits, allowing increased efficiency and reliability of the current source. Spot Welding - spot welding, with the ability to set the welding time at the point, available with Puls MIG welding. HOT START (hot start) - a function that makes starting welding much easier. At the moment of arc ignition, the welding current is briefly increased. This leads to the heating of the material and the electrode at the point of contact, as well as to the appropriate formation of the fusion and the weld face (in the initial phase of the welding process). ARC FORCE - a function that provides the best settings to achieve a stable arc and a low amount of spatter. In other words, with ARC FORCE, the electric arc required for welding glows in a steady manner, without short circuits that hinder or prevent the joining of materials. Welding often produces large amounts of spatter, or droplets of molten metals, which must be removed. When the ARC FORCE function is activated, the amount of spatter is significantly reduced, and this allows for more comfortable work. ANTI STICK: anti-short-circuit - automatically shuts off the welding voltage if the electrode sticks to the material being welded, which makes it easier to peel it off and prevents accidental welding arc. The device has a fan-cooling system that is activated only when needed, which dramatically increases its efficiency and reduces contamination inside the device. The price of the device with a set of MIG / MMA accessories: MB 15/3 welding chuck - ground cable with 200A clamp 2m power cord with 230V plug 8mm hose connector for connecting the gas hose electrode holder 200A - 2M Hammer brush Welding gloves Gas hose New 8l cylinder filled with CO2/AR Painted according to the Polish Standard. Cylinders filled. Very light and efficient. Cylinders and valves meet the standard EN 1964-1 Legalization 10 years replaceable at any distributor . Welding wire Sg2 0,8/5 K G Anti-splinter SPRAY Welding gloves consumable elements of the welding gun Mini Co2/AR reducer Welding visor APS 510G 2 welding bevels 12 Kg Device parameters Mains protection: C25A Rated supply voltage 230 V; 50Hz (1ph) Power: 6.7 kW 65 V idle voltage Maximum current: 200 A (MIG) / 180 A (MMA) Current at 100% operation: 155 A Current at 60% operation: 200 A (MIG) / 180 A (MMA) Aluminum wire diameter: 0.8 - 1.0 mm Diameter of self-stripping wire: 0.8 - 0.9 mm Diameter of steel wire: 0.6 - 1.0 mm Stainless steel wire diameter: 0.6 - 0.8 mm Welding electrode diameter: 1.6 - 4.0 mm Welding current adjustment range: 40 - 200 A Wire spool size: D200 (2kg and 5kg) Degree of protection IP 23 Weight of the device / set: 12 / 15 kg Overall dimensions L x W x H: 465x190x370 mm Package dimensions L x W x H: 640x280x460 mm APS welding visors with variable degree of protection DIN 4/9-13, variable brightening time and adjustable sensitivity of sensors.Designed for MIG/MAG, TIG and TIG PULSE and MMA welding, equipped with grinding function.High-quality LCD filters in optical class 1/1/1/2.Power source: photovoltaic cell + replaceable battery.4-arm adjustable headpiece provides comfort.Shell compliant with EN175B for greater impact resistance. Plasma cutting: MIG/MAG ; MMA: Grinding: TIG, minimum current value: ?, >10A. Response time: