Soldering station + soldering iron 2-in-1 Yihua 948-I Yihua 948-I soldering station including tin soldering iron and head soldering iron. With efficient heating elements, it allows you to quickly and conveniently solder/solder all electronic components. Soldering iron built with regard to ESD standards, so you are assured that you will not damage electronic components during service. Yihua 948-I soldering station corrects the set temperature in real time, thanks to its precise PID controller, this makes the soldering station have high temperature stability, even with large fluctuations in heat pickup. The power supply of the station is based on transformer with good insulation of heating elements, which makes it possible to achieve high reliability and safe operation. The device has the following functions: Operation in C/F mode. Ability to set on the display in which units the temperature will be displayed. Sleep function: each time heating up and cooling down would generate a lot of wasted time. Therefore, a sleep function has been added to the station, so that when you put the flask on the stand, this flask after a predetermined time (5,10,15,20, or 30 minutes) will go into sleep mode, and the temperature will drop to 200 degrees. When the flask is picked up again, it will take much less time to heat up to the earlier temperature. As a result, the power consumption drops, the soldering tip wears out much more slowly. It is possible to disable this function by setting the time to 0. The function works both for soldering iron and soldering iron. Automatic shutdown function, the soldering station in order to save energy goes into sleep mode, if it is not awakened from it can automatically turn off. Time setting range: 1 to 99 minutes in 1-minute steps. The station has two connectors, one for the soldering iron and the other for the desoldering iron, only one of them can be worked on at the same time. Compensation function temperature, there are many types of tips, some are long and thin others are short and thick which leads to different thermal conductivity of these tips and thus different temperatures at their tips. Here with help comes the function of temperature compensation, thanks to which we can correct the excess or deficiency of temperature in the range of +/-50 degrees. The function is useful especially in professional applications. The flask of the desoldering machine has a special design thanks to this soil enters the tin container in a molten state, this increases the efficiency of work and reduces the frequency of regular maintenance. The function of on/off key sound to change the temperature.️ The rotors of the soldering iron are sealed with tin at the factory, the tin will melt after the first use of the gun. ️️ Whenever you use it with the soldering iron, wait until it has heated up to the set temperature. During this time, the set temperature reading flashes (indicates heating) Start working after the flashing stops when you hear a beeping sync ️ Specifications:️ Power supply: 230V️ Rated power: 90W️ Display: LED️ Dimensions: 234x202x134mm +/-5mm (Lx W x H)️ Ground resistance of the arrowhead: <2 Ohm Parameters of the soldering iron:️ Heating power : 75W️ Temperature range: 350 ℃ ～ 480 ℃ / 662 ℉ ～ 896 ℉️ Temperature stability: +/-1°C️ Flask cable length: up to 120cm️ Compressor power: 12W️ Vacuum pressure: 0.05 MPa Soldering iron parameters:️ Heater power 75W️ Temperature range 200 ℃ ～ 480 ℃ / 392 ℉ ～ 896 ℉️ Mounted soldering tip900M T-.B️ Flask equipped with 131A heater️ Heat resistant cable️ Cable length: 90cm Included:1️⃣ Yihua 948-I station2️⃣ Pistol flask holder with sponge3️⃣ Soldering gun 8pin4️⃣ Soldering flask 907I + 2 soldering tips ( including 1 put on the gun)Spare filters:5️⃣ 2 pcs. white for tank6️⃣ 5pcs black for station7️⃣ Spare spring filters 2 pcs.8️⃣ Complete plastic tin tank9️⃣ Vacuum hose holder 2pcs. (including 1 attached to the station)1️⃣0️⃣ Pin1️⃣1️⃣ Set of cleaning notches for cleaning arrowheads of different thicknesses1️⃣2️⃣ Power cord for changing blades1️⃣3️⃣ Silicone pack