TX 6222V precision guide and drawbar lathe - DPA32-3

Strongly ribbed cast iron machine bed One-piece steel machine base High rigidity of headstock housing due to strongly ribbed 25GG cast iron Precision-machined slide Shafts on needle bearings, all components lubricated in oil bath Bed guides hardened and precision ground Access to all electronic controls centrally All gearsAll electronic controls are accessible centrally All feed gears are made of steel, hardened and precision ground Hand gears decoupled and tested according to EN 23125Right/left dual channel switch tested according to EN 23125Switch with life cycle calculation, tested according to EN ISO 13849Cooling system with separate 50 liter coolant tank with level indicator and oil separator; easy and complete emptying and cleaning in accordance with DIN Complete callout and drawbar guard Complete work area lighting Hardened and ground spindle face for extreme accuracy and durability. High chip removal during roughing is not a problem thanks to high chip removal capacity The lockable chip guard moves with the bed guide with integrated position indicator and coolant hose, Moves manually No gearbox replacement required . With protection against simultaneous operation of tapping and feed Electronically braked motor Electronic Z-axis feed cut-off Electronic position cut-off with quadruple position stop. Triangular lathe chuck as standard equipment Switchable steel chuck SWH 7-C Stainless steel chuck 32 x 130 type D for 25 mm square chisel Digital position indicator DPA 32-3 . With electronically adjustable drive and digital position indicator DPA 32-3 Strongly ribbed cast iron machine bed One-piece steel machine base High rigidity of headstock housing due to strongly ribbed 25GG cast iron Precision machined slide Shafts on needle bearings, all components lubricated in oil bath Bed guides hardened and precision ground Access to all electronic controls centrally All gearsAll electronic controls are accessible centrally All feed gears are made of steel, hardened and precision ground Hand gears decoupled and tested in accordance with EN 23125Right/left dual channel switch tested in accordance with EN 23125Switch with life cycle calculation, tested in accordance with EN ISO 13849Cooling system with separate 50 liter coolant tank with level indicator and oil separator; easy and complete emptying and cleaning according to DIN Complete drawbar and drawbar guard Complete work area lighting Hardened and ground spindle face for extreme accuracy and durability. High chip removal during roughing is not a problem thanks to high chip removal capacity The lockable chip guard moves with the bed guide with integrated position indicator and coolant hose, Moves manually No gearbox replacement required . With protection against simultaneous operation of tapping and feed Electronically braked motor Electronic Z-axis feed cut-off Electronic position cut-off with quadruple position stop. Triple-jaw lathe chuck as standard equipment Switchable steel chuck SWH 7-C Stainless steel chuck 32 x 130 type D for 25 mm square chisel Digital position indicator DPA 32-3 . Dimensions and weights. Length (product) approx: 3605Width/depth (product) approx.: 1739. Height (product) approx.: 1905. Weight (net) approx: 2800Working areas. Height of center: 310Highest level: 2225. Machine bed clearance: 620Swing diameter at bed bridge: 880. Swing diameter over longitudinal guide: 580Swing over cross slide: 424Turning length in bed bridge: 231Speed range. Number of speed ranges: 2 x 3Speed range: 14 - 1800Electrical data. Drive motor power: 11Power supply voltage: 400Power frequency: 50 Power frequency: 50. Coolant system. Coolant system Coolant pump power: 0.1. Spindle. Spindle shank: Camlock DIN ISO 702-2 No. 8 Steel shank. Steel shank: SWH 7-CSpindle bore/spindle passage Diameter: 105. Spindle taper: MT 7. Tailstock. Tailstock attachment: MT 5Tailstock quill stroke: 180Tailstock quill diameter: 72Tilt. Slope metrics: 0.5 - 15. Metric pitch count: 55. Inch pitch: 60 - 2Number of pitches Inch: 55Number of Diametric Pitch: 120 - 4. Number of Pitch Diameter Pitch: 55Thread modulus pitch: 0.25 - 7.5. Number of pitch Modulus thread: 55Guide screw pitch: 6Transverse path. Top slider travel: 170Cross slide travel: 350Slide of bed slide: 2000. Propulsion. Longitudinal feed range: 0.05 - 1.5. Number of longitudinal feeds: 55Planar feed range: 0.025 - 0.75. Number of feeding plans: 55Feed motor Drive power. Feed motor Drive power: 0.55. Electrical connection. Total connected load: 12