Magnum THF 335P AC/DC

The MAGNUM THF 335P AC/DC is a professional inverter welder designed for manual electric TIG welding. with AC current . and DC. The device can also be used for MMA welding using fusible covered electrodes. The device can also be used for MMA welding using fusible covered electrodes. The MAGNUM THF 335P welder is powered from a 400V three-phase grid, and has a high 60% duty cycle at 300 A. It is designed for all kinds of welding work in locksmith shops, repair shops, industrial workshops, factories, etc. The device is equipped with a large, clear soft: control panel that allows you to set all the necessary welding functions : . current: start/ crater fill/weld/base, current rise and fall time, . gas outflow before and after welding, . pulsation frequency, balance, etc.. The current source is built on IGBT transistors to ensure minimum electromagnetic interference and low power loss, enabling increased efficiency and reliability. reliability of the current source. Very high efficiency, which translates directly into lower power consumption, and high switching frequency, provide instant decision-making modulation. adaptation of current to changes in parameters during welding. The digital function panel allows precise control and selection of all the most important welding parameters: . - TIG AC, TIG DC, MMA welding method selection - 2T/4T operation mode - TIG pulse: on/off - AC balance - AC current frequency - Gas discharge before welding - Initial current - Welding current rise time - Peak welding current value, when welding with TIG Puls method - Welding current value, when welding with MMA and TIG method - Frequency of welding current pulsation for TIG Puls method - Pulsation balance- ratio of peak current to base current for TIG Puls method - Descending time of welding current to final current value - Final current - Gas discharge time after welding The MAGNUM THF 335P AC/DC is a professional inverter welder designed for manual electric TIG welding. with AC current . and DC. The device can also be used for MMA welding using fusible covered electrodes. The device can also be used for MMA welding using fusible covered electrodes. The MAGNUM THF 335P welder is powered from a 400V three-phase grid, and has a high 60% duty cycle at 300 A. It is designed for all kinds of welding work in locksmith shops, repair shops, industrial workshops, factories, etc. The device is equipped with a large, clear soft: control panel that allows you to set all the necessary welding functions : . current: start/ crater fill/weld/base, current rise and fall time, . gas outflow before and after welding, . pulsation frequency, balance, etc.. The current source is built on IGBT transistors to ensure minimum electromagnetic interference and low power loss, enabling increased efficiency and reliability. reliability of the current source. Very high efficiency, which translates directly into lower power consumption, and high switching frequency, provide instant decision-making modulation. adaptation of current to changes in parameters during welding. The digital function panel allows precise control and selection of all the most important welding parameters: . - TIG AC, TIG DC, MMA welding method selection - 2T/4T operation mode - TIG pulse: on/off - AC balance - AC current frequency - Gas discharge before welding - Initial current - Welding current rise time - Peak welding current value, when welding with TIG Puls method - Welding current value, when welding with MMA and TIG method - Frequency of welding current pulsation for TIG Puls method - Pulsation balance- ratio of peak current to base current for TIG Puls method - Descending time of welding current to final current value - Final current - Gas discharge time after welding RANGE OF PARAMETER REGULATIONS:. gas before- time of gas outflow before welding: 0.3 - 10 [s]. Ip - initial current: 10-315 [A] tn - rise time of Ip current to ls/b: 0 - 10 [s] Imax - peak TIG pulse current: 10 - 315 [A]. Is/b - TIG welding current, TIG pulse base current: 10 - 315 [A]. pulse [Hz] - frequency of TIG pulse current: 0.5 - 100 [Hz]. puls [%] - current balance (peak to base) TIG pulse: 1- 99 [%]. to - time of falling current Is/b to Ik: 0 - 10 [s]. Ik - final current: 10 - 315 [A] gas after - time of gas discharge after welding: 1 - 30 [s] AC frequency - frequency of polarity change: 50- 150 [Hz] AC balance [%] - polarity change balance: 20 - 50 [Hz] TECHNICAL DATA: Power supply: AC 400 [V], 50/ [Hz],. Required protection: 25 [A] / C Power consumption: 9.6 [kW] Operating cycle: 60 [%]. Idle voltage Uo: 68 [V] TIG AC welding current: 10 - 315 [A]. DCTIG welding current: 10 - 315 [A]. MMA welding current: 10 - 240 [A]. Casing protection class: IP23. Weight: 24.3 [kg].