MAGNUM MIG 210/2 MMA 230/400V 15 KG welding machine.

This device is used in locksmith workshops as well as in repair shops. It allows welding with steel welding wires with a diameter of 0.6-0.8 mm, as well as with self-shielded wires (welding ""without gas"") and electrodes with a diameter of 1.6-3.2 mm. MIG 210/2 IGBT MMA is a device adapted to be powered from a single-phase network 230 V, 50 Hz/ 400V . This device is equipped with an overload thermal protection system to prevent excessive overheating. The MIDI MIG 210/2 series device by MAGNUM is a semi-automatic welding machine designed for manual electric welding of low-carbon steel, low-alloy steel (MAG), alloy steel (MIG) and aluminum and its alloys. It has the ability to weld with self-consuming wire - FCAW (it is necessary to change the polarity in the welder: minus (-) on the welding handle, plus (+) on the ground!), and the MMA method using fusible covered electrodes. It is designed for all kinds of welding work in locksmith workshops, repair shops, industrial workshops, factories, etc. The welder has a stepless adjustment of welding parameters, a thermal protection system to prevent excessive heating of the device. It is equipped with a two-roll wire feeder and the function of automatic detection of 230 V / 400 V supply voltage. This device is used in locksmith workshops as well as in repair shops. It allows welding with steel welding wires with a diameter of 0.6-0.8 mm, as well as with self-shielded wires (welding ""without gas"") and electrodes with a diameter of 1.6-3.2 mm. MIG 210/2 IGBT MMA is a device adapted to be powered from a single-phase network 230 V, 50 Hz/ 400V . This device is equipped with an overload thermal protection system to prevent excessive overheating. The MIDI MIG 210/2 series device by MAGNUM is a semi-automatic welding machine designed for manual electric welding of low-carbon steel, low-alloy steel (MAG), alloy steel (MIG) and aluminum and its alloys. It has the ability to weld with self-consuming wire - FCAW (it is necessary to change the polarity in the welder: minus (-) on the welding handle, plus (+) on the ground!), and the MMA method using fusible covered electrodes. It is designed for all kinds of welding work in locksmith workshops, repair shops, industrial workshops, factories, etc. The welder has a stepless adjustment of welding parameters, a thermal protection system to prevent excessive heating of the device. It is equipped with a two-roll wire feeder and the function of automatic detection of 230 V / 400 V supply voltage. The current source is built on IGBT transistors that provide a minimum of electromagnetic interference, enabling increased efficiency and reliability of the current source, lower power consumption and instantaneous adjustment of current to changes in parameters during welding. Features and advantages: inductance control welding without FLUX gas 230/400 V POWER SUPPLY stepless parameter adjustment MIG/MAG welding Wire spools from 1-15 KG Possibility of brazing and welding of aluminum MMA welding MIG EUR 15/3M holder Strong solid chassis Adapter 400/230V WELDING CURRENT 30-200 A Efficiency 200A /60% Metal solid wire feeder It is designed for all kinds of welding work, in locksmith workshops, repair shops, industrial workshops, factories, etc. The current source is built on IGBT transistors to ensure a minimum of electromagnetic interference, low power loss in the basic circuits, allowing to increase the efficiency and reliability of the current source, lower power consumption, and instant adaptation of current to changes in parameters during welding. Due to its low weight and dimensions, it is ideal for: construction companies car repair shops locksmith workshops households FCAW - the possibility of welding with cored wire without the use of gas cylinders. The wire itself (FLUX) is filled with a substance that produces gases during welding. Adjustable inductance - allowing less heat to be introduced into the welding area. The sheet metal does not deform and the protective zinc layer is not damaged, useful in soldering. BUTOSWELDING - is a method that is quite similar to MIG/MAG welding, but the energy supplied in this case is much less. This makes solder welding used for joining thin zinc-coated sheets. The method described is a welding process, during which the solder, not the material you are working with, is melted. The second part of the name, MIG/MAG, comes from the use of the method of melting the wire in an electric arc surrounded by a protective gas, as well as preparing the edge of the material in the same way as for traditional welding. However, the brazing method is used not only to weld galvanized sheet metal, but also thin sheets made of stainless steel and dissimilar joints, including acid-resistant steel with ordinary steel or copper with steel. IGBT - the welder uses modern transistors, a solution that ensures a minimum of electromagnetic interference low power losses in the basic circuits, allowing to increase the efficiency and reliability of the current source. The set includes: MIG 210/2 MMA IGBT unit MIG holder 3 meters Ground holder Electrode holder 400v/230v adapter consumable parts of the welding gun Welding shield Gas hose Welding gloves Hammer-brush Specifications: Welding current: 30-200A Efficiency: 60% Power supply: 230V / 400V Power supply protection: 20A Reel weights used: 1-15 kg Enclosure protection: IP21 Cooling: fan Gas-free welding: Yes Weight 19.5 kg Wire diameter 0.6/0.8/1.0 1. wire ejection button. 2. MIG-MAG / MMA welding method selection switch. 3. display. 4. socket for connecting the MIG-MAG holder (euro-socket). 5. Welding current adjustment knob for MIG-MAG and MMA. 6. wire feed speed adjustment knob for MIG-MAG. 7. Indicator light for safety system tripping. 8. main switch 9. output socket with positive polarity. 10. output socket with negative polarity. 11. Plug on the cable for selecting the polarity for the MIG-MAG method.