Hot air soldering station 720W - 75W New Design 3 memory, YH-995D+ ND WEP 995D+ ND soldering station is a 2-in-1 soldering station for: - Hot air, used for desoldering and soldering electronic circuits such as BGA, SMD and etc. The source of air supply is a fan. - A more powerful yellow-blue colored grotto flask with a peak power of 72-75W (original Japanese-made Hakko heating element) WEP 995D+ND soldering station is suitable for soldering and desoldering electronic components like SOIC, CHIP, QFP, PLCC, BGA, SMD, tid (especially cell phones). The station is used for soldering and desoldering electronic components, shrinking, welding plastics, heating. The WEP 995D+ND soldering iron is a hot air soldering station and a soldering tip. The station is equipped with a PID microprocessor, which checks the station's operating parameters in 20ms cycles and corrects them to the set values. The values of temperature, airflow power, operating mode, are visible on a large easy-to-read LCD display, which greatly facilitates the work. The hotair soldering iron is equipped with a ceramic heating element, which heats up quickly and evenly. The heater is made of hard alloys, allowing long working time at high temperatures, while not deforming, this greatly increases the stability of work and extends the life of the heater. Standard size hotair flask - fits all nozzles available in our offer. There is a micro-contact in the hotair flask holder, which, when the flask is put down, causes the flask to go into standby mode, by cooling the heating element and then turning off the air supply. This extends the life of the heater and saves electricity, which is very fashionable lately and needed to protect the environment. The station is equipped with functions for checking the correct operation, we receive messages about a short circuit, overloading of circuits, failure to achieve the set temperature. All these errors are shown on the display. Choosing the automatic operation mode, when we put the hot flask down on the stand, the device will automatically stop heating and cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service. The soldering iron is distinguished by such features: - 3 Work Programs. The soldering station has the ability to store 3 work programs for hot air and flask. Depending on the type of work assembly, disassembly, set the appropriate program. - Hot air operation in automatic/manual mode. Choosing the automatic operation mode, when you put the hot air flask on the stand, the device will automatically stop heating and cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service. Choosing the manual mode, when we often need to solder something, then we save time and increase the efficiency of work. It is recommended before finishing work, to switch to automatic mode. - Temperature correction function. It depends on the working environment, the efficiency of the heating element, the power of the blowing, the consumption of the mainsheet, all this affects the appropriate temperature correction to obtain the set parameter. - Operation in C/F mode. Possibility to set on the display in which units the temperature will be displayed. - Sleep function for the mains soldering iron. The soldering iron is equipped with a sleep mode, when the flask is not used, after a pre-set time in the range of 0-99min it goes into sleep mode, i.e. the flask is heated to a temperature of 200C, this prevents excessive oxidation of the mainsail, and this affects its life and the heating element. We have the option to disable the mode by setting 0. Technical data: - voltage 220-240V - power consumption 720W - working environment from 0 to 50°C - compact design with easy-to-read LCD display. - PID controller - microprocessor control of parameters: temperature, blowing power, operating time, temperature correction - protection against reaching too high temperature and informing with an alarm. - possibility to save 3 working programs (temperature, blowing power) - Cooling function - F/C temperature display mode - gross weight: 3.21kg Hot air station: - air supply source: Fan - air flow: up to 120 L/min - infinitely adjustable temperature over the entire range. - temperature range: 100-480°C - temperature stability: ±1°C - display type: LCD Included: - WEP 995D+ ND soldering station - hotair flask stand - set of nozzles: - round nozzle with a diameter of 4.4 mm 1130 - round nozzle with a diameter of 8 mm 1195 - round nozzle with a diameter of 9 mm 1197 - square nozzle 12x12 mm 1313 - mainsail base with cleaning sponge - 907F mainsail flask with T-I type 900M mainsail (Hakko heating element) - chip picker - power cord