Hot air soldering station

Hot air soldering station WEP 995D soldering station is a 2-in-1 soldering station for: - Hot air, used for desoldering and soldering electronic circuits such as BGA, SMD and etc. Blowing in the station is achieved by a fan. - More powerful 60W yellow-blue colored grotto flask (original Japanese-made Hakko heating element) WEP 995D soldering station is suitable for soldering and desoldering electronic components like SOIC, CHIP, QFP, PLCC, BGA, SMD, tid (especially cell phones). The station is used for soldering and desoldering electronic components, shrinking, welding plastics, heating. The WEP 995D soldering iron is a hot air soldering station and a soldering tip. The station is equipped with a PID microprocessor, which checks the station's operating parameters in 20ms cycles and corrects them to the set values. The values of temperature, airflow power, operating mode, are visible on a large easy-to-read LCD display, which greatly facilitates the work. The hotair soldering iron is equipped with a ceramic heating element, which heats up quickly and evenly. The heater is made of hard alloys, allowing long working time at high temperatures, while not deforming, this greatly increases the stability of the work and extends the life of the heater. There is a micro contact in the hot air flask holder, which, when the flask is put down, causes the flask to go into standby mode, by cooling the heating element and then turning off the air supply. This extends the life of the heater and saves electricity, which is very fashionable and necessary lately to protect the environment. The station is equipped with functions for checking the correct operation we receive messages about a short circuit, overloading of circuits, failure to achieve the set temperature. All these errors are shown on the display. Choosing the automatic operation mode, when we put the hot flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service. The soldering iron is distinguished by such functions. - Hot air operation in automatic/manual mode.Selecting the automatic operation mode, when you put the hot air flask on the stand, the device will automatically stop heating and cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service. Choosing the manual mode, when we often need to solder something, then we save time and increase the efficiency of work. It is recommended before finishing work, to switch to automatic mode. - Temperature correction function. It depends on the working environment, the efficiency of the heating element, the power of the blowing, the consumption of the mainsheet, all this affects the appropriate temperature correction to obtain the set parameter. - Operation in C/F mode. Possibility to set on the display in which units the temperature will be displayed. - Sleep function for the mains soldering iron. The soldering iron is equipped with a sleep mode, when the flask is not used, after a pre-set time in the range of 0-99min it goes into sleep mode, i.e. the flask is heated to a temperature of 200C, this prevents excessive oxidation of the mainsail, and this affects its life and the heating element. We have the option to disable the mode by setting 0. Technical specifications: - Voltage: 220-240 V - Power consumption: 700W - Compact design with easy-to-read LCD display. - PID controller - Microprocessor control of parameters: temperature, blowing power, operating time - F/C temperature display mode Hot air station: - Airflow: Fan - Air flow rate: up to 120 L/min - Infinitely adjustable temperature over the entire range. - Temperature range: 100-480°C - Temperature stability: +/-1oC - Display type: LCD - Cable length in flask: up to 100cm - Manual / automatic operation mode - Protects against reaching too high a temperature and informs you with an alarm. - Displays the actual blowing power Grotto station: - Temperature range: 200-480°C - Temperature stability: +/-1oC - Display type: LCD - Resistance to ground less than to 2ohm - Potential to ground less than up to 2mV - System: ESD safe - Flask cable length: up to 100cm - Sleep mode: activated after idle 0-99 minutes. - Heating element 50W peak power when heating up 75W peak power can be as high as 140W - Peak power consumption 75W Included - WEP 995D soldering station - Hotair flask stand - Set of nozzles: - 4.4 mm diameter round nozzle 1130 - round nozzle with a diameter of 8 mm 1195 - round nozzle with a diameter of 9 mm 1197 - square nozzle 12x12 mm 1313 - Blade flask stand including cleaning sponge - Blade flask with T-I blade - Gripper for lifting the circuits - Power cord