Precision guide and drawbar lathe TX 6222

Machine base made of heavily ribbed cast ironOne-piece machine base made of steelHigh rigidity of headstock housing due to heavily ribbed 25GG castingAll feed gears made of steel, hardened and groundShafts on needle bearings, all components are lubricated in an oil bathHardened and ground spindle provides great accuracy and durabilityThrough high cutting performance, removing large amounts of chips during roughing is not a problemService-friendly removable rear panelPower chain for smooth routing of hoses and cablesChip guard slides together with bed guide with integrated position indicator and coolant hose, slidable by handDisengageable handwheels tested to EN 23125Two-channel right-hand switch- two-channel right-hand switch-left tested to EN 23125No change of wheels necessarySwitch with life cycle calculation tested to EN ISO 13849Protected against simultaneous operation of threading mechanism and feedBed guides hardened and precision groundElectronically braked motorElectronic axis feed disengagement. ZAll electronic controls centrally accessibleFull illumination of work areaExternal coolant reservoir with level indicator and oil separatorComplete guards for guiding and tensioning spindleElectronic position cut-off with quadruple position stopTurning chuck 3-jawjaw chuck in the standard scope of supplySwitchable steel chuck SWH 7-C1 steel chuck 32 x 130 type D for 25 mm square chiselDigital position indicator DP700 (for more information see "NEWALL-.DP700")TX 5216Large spindle bore Ø 80 mmTX 6222:Large spindle bore Ø 105 mm. meets the highest requirements in terms of technical equipment and precision. With digital position indicator NEWALL DP 700 Machine base made of heavily ribbed cast ironOne-piece machine base made of steelHigh rigidity of headstock housing due to heavily ribbed 25GG castingAll feed gears made of steel, hardened and groundShafts on needle bearings, all components are lubricated in an oil bathHardened and ground spindle provides great accuracy and durabilityThrough high cutting performance, removing large amounts of chips during roughing is not a problemService-friendly removable rear panelPower chain for smooth routing of hoses and cablesChip guard slides together with bed guide with integrated position indicator and coolant hose, slidable by handDisengageable handwheels tested to EN 23125Two-channel right-hand switch- two-channel right-hand switch-left tested to EN 23125No change of wheels necessarySwitch with life cycle calculation tested to EN ISO 13849Protected against simultaneous operation of threading mechanism and feedBed guides hardened and precision groundElectronically braked motorElectronic axis feed disengagement. ZAll electronic controls centrally accessibleFull illumination of work areaExternal coolant reservoir with level indicator and oil separatorComplete guards for guiding and tensioning spindleElectronic position cut-off with quadruple position stopTurning chuck 3-jawjaw chuck in the standard scope of supplySwitchable steel chuck SWH 7-C1 steel chuck 32 x 130 type D for 25 mm square chiselDigital position indicator DP700 (for more information see "NEWALL-.DP700")TX 5216Large spindle bore Ø 80 mmTX 6222:Large spindle bore Ø 105 mm. Dimensions and weights. Length (product) approx: 3550Width/depth (product) approx.: 1200. Height (product) approx.: 1830. Weight (net) approx: 2800Working areas. Height of center: 310Highest level: 2200. Machine bed clearance: 620Swing diameter in bed bridge: 880. Swing diameter over longitudinal guide: 580Swing over cross slide: 424Turning length in bed bridge: 880Bed width: 350. Speed range. Number of speed ranges: 12Speed range: 30 - 1500Electrical data. Power of drive motor: 7.5Power supply voltage: 400Network frequency: 50. Coolant system. Coolant system Coolant pump power: 100Spindle. Spindle shank: Camlock DIN ISO 702-2 No. 8 Spindle bore. Spindle bore/spindle passage Diameter: 105. Spindle taper: MT 7. Tailstock. Tailstock attachment: MT5Tailstock quill stroke: 180Tailstock quill diameter: 72Tilt. Slope metrics: 0.5 - 15. Metric pitch count: 55. Inch pitch: 60 - 2Number of pitches Inch: 55Number of Diametric Pitch: 120 - 4. Number of Pitch Diameter Pitch: 55Thread modulus pitch: 0.25 - 7.5. Number of pitch Modulus thread: 55Transverse path. Top slider travel: 170Cross slide travel: 350Slide of bed slide: 2000. Propulsion. Longitudinal feed range: 0.05 - 1.5. Number of longitudinal feeds: 55Planar feed range: 0.025 - 0.75. Number of feeding plans: 55Electrical connection. Total connected load: 8.5