STILER BS 912B band saw machine

Original STILER BS 912B belt cutter NEW POWERFUL MODEL. PROFESSIONAL, VERY POWERFUL AND EFFICIENT Widely used in locksmith, manufacturing, craftsmen's workshops. The new model uses a more powerful three-phase motor equipped with additional protection, a new generation maintenance-free hydraulic cylinder, liquid cooling in a closed system with a large drainage tank. Additionally, the guides have been equipped with carbide, which translates into greater accuracy in serial cutting. Main advantages of the machine are: rotary vise up to 45º, new generation hydraulic cylinder, more powerful 1.1 kW 400V motor, more efficient cooling system. The machine is equipped with a vise knob and quick clamping which speeds up the replacement of the cut profile. Bearing guides provide secure and even guidance of the tape in the cut workpiece. In addition, at the bearings are mounted, carbide which improves accuracy in serial cutting. A big plus is the cooling of the cutting belt located directly on the guide. In the set bumper for the length of the cut material. The speed of the belt is changed after the V-belt on the pulleys. Such a solution gives us a wide range of cutting speed 26/50/73/95 m/min. Hydraulic cylinder with stepless arm drop adjustment, facilitates more accurate speed setting to the material being cut. Specification: The material to be cut can be fed manually or by any mechanical device. On the other hand, the feed of the tool is done automatically. The speed of the arm descent is regulated by a hydraulic cylinder. The appropriate speed of the arm descent is obtained through a valve regulating the flow of oil between the chambers of the actuator. The desired linear speed of the belt is obtained by changing the ratio on the pulleys between the worm gear and the drive motor. In the base there is a coolant tank with an electropump. Precision and solidity of manufacture puts it at the forefront of belt cutters with such a large cutting capacity because 230 mm and at any angle from 0 to 45 degrees. Belt cutter STILER BS 912B thanks to innovative improvements in combination with bi-metal blades from a renowned company is widely used in all locksmith shops where precision, quality and accuracy and speed of cutting count. The cutting angle is set by a rotary vise in the range from 0 - 45*. Massive vise walls are made of resistant cast iron. On the back of the vise, we have an angle scale for convenient and fast setting of the cutting angle. Both belt guides are equipped with a cooling system that feeds coolant to the belt and the cut workpiece. This model of the cutting machine is equipped with a convenient handle for tensioning the belt and quick pressure of the vise (cut workpiece). On the arm of the machine we have located the tape tension indicator and a table for the selection of belt toothing and cutting speed depending on the grade of steel we will be cutting. In the lower position of the arm ( after cutting the material) the cutting belt drive is switched off automatically through a new generation limit switch. Safety during the cutting process is ensured by the electrical installation that meets all CE requirements. The machine has a limit switch that stops the machine when the cutting process is finished, an emergency switch, the so-called "safety mushroom", a number of micro switches that turn off the machine when, for example: we open the belt transmission cover or the cutting belt cover. Additionally, our machine model is equipped with a wire brush that cleans the cutting belt of chips - this prevents clogging of the blade and gives more efficient cutting. The belt guides are equipped with special carbide plates and bearings. This has a huge impact on the guidance of the tape, its life, straightness, accuracy and quality of cutting. Carbide guidance reduces to a very large extent the wear and tear of the machine and the blade itself !!! The arm made of profiled ductile iron provides rigidity during operation and absorbs all kinds of vibration. The control panel is located on the arm of the cutting machine. Technical data Model: BS 912B Power: 1.1 kW Power: 400V, 3 phases Cutting belt size: 2655x27x0.9 mm Arm drop adjustment: Hydraulic actuator Belt linear speed: 26/50/73/95 m/min Distance of the vise base from the ground 550 mm Net / gross weight: 190 / 250 kg Cutting range Angle Tube PROFILE CADRAT. 0º ø230 310 x 180 230 x 230 45º ø150 150 x 130 150 x 150.