STILER band saw G5027

The band saw STILER G5027 allows cutting in a plane perpendicular to the axis of the material being cut or at any angle from -45 to +60 degrees. The advance during cutting is carried out by gravity on the principle of oil flow in a two-chamber hydraulic cylinder. The appropriate speed of the arm's descent is set using a regulator located on the control panel. A cast iron work table with a rotating arm and a control panel on a separate pedestal is attached to the base. You can set the speed of the cutting belt on it, as well as turn the machine on/off. There is a choice of two cutting belt speeds, 36 and 72 m/min. The machine is equipped with a roller that feeds the material to be cut and a bumper for the length of the material to be cut. The cutting machine is located in an adjustable bed and is equipped with a quick press. The base is built as a rigid body welded from steel sheets. Inside, there is a separate coolant tank with an electric pump and a large drainage sump. The shape of the upper part of the base provides a sump for draining coolant and catching chips generated during material cutting. SPECIFICATION: The cutter arm made of a uniform cast iron casting together with the 27 mm wide cutting belt used in this cutter. allows you to fully perform multi-series cuts of both profiles and solid materials. STILER G5027 allows you to cut a whole range of materials from black steel, pipes, profiles, channels ending with grade steel, stainless steel , acid and solid materials. Belt guides are equipped with special carbide plates and bearings. This has a tremendous impact on the belt guidance, its life, straightness, accuracy and quality of cutting. In the lower position of the arm ( after cutting the material) the cutting belt drive and cooling system is switched off automatically. Safety will be ensured by cutting belt guards and micro switches that stop the motor when the cutting cycle is completed or when any of the guards are opened, an additional safety feature is the automatic shutdown of the cutter if the cutting belt breaks. The motor is equipped with new generation thermal fuses. The drive from the motor to the belt drive wheel is transferred by a maintenance-free worm gear. Roller feeders - as an additional option - available on our other auctions. Belt cutter type STILER G5027 allows cutting in a plane perpendicular to the axis of the material being cut or at any angle from -45 to +60 degrees. The feed during cutting is carried out by gravity on the principle of oil flow in a two-chamber hydraulic cylinder. The appropriate speed of descent of the arm is set by means of a regulator located on the control panel. The arm of the cutter made of a uniform cast iron casting together with the 27 mm wide cutting belt used in this cutter. allows you to fully perform multi-series cuts of both profiles and solid materials. The vice is located in the adjustable bed and is equipped with a quick clamping device. STILER G5027 allows you to cut the entire range of materials from black steel, pipes, profiles, channels ending with grade steel, stainless steel , acid and solid materials. Belt guides are equipped with special carbide plates and bearings. This has a huge impact on the guidance of the belt, its life, straightness, accuracy and quality of cutting. Included is a roller feeding the material to be cut and a bumper for the length of the cut material. The speed of the cutting belt is regulated on the control panel of the cutting machine. There are two speeds to choose from : 36 and 72 m/min. In the lower position of the arm ( after the material has been cut), the cutting belt drive and the cooling system are switched off automatically. Safety will be ensured by the cutting belt guards and micro switches that stop the engine when the cutting cycle is completed or when any of the guards are opened, an additional safety feature is the automatic shutdown of the cutting machine in case the cutting belt breaks. The motor is equipped with new generation thermal fuses. The base is built as a rigid body welded from steel sheets. Inside, there is a separate coolant tank with an electric pump and a large drainage sump. The design of the upper part of the base provides a sump for draining coolant and catching chips generated during material cutting. A cast-iron work table with a rotating arm and a control panel on a separate pedestal is attached to the base. In the cutting process, the main cutting motion is the movement of the cutting belt. The drive from the motor to the belt drive wheel is transmitted by means of a worm gear. Technical data Model: G5027 Power: 2.2 kW Power supply: 400V, 3 phase Cutting belt size: 2950x27x0.9 mm Regulation of arm descent: Hydraulic cylinder Belt linear speed: 36/72 m/min Distance of vise base from ground 940 mm Weight: 480 kg Cutting range Angle TUBE PROFILE CADRAT 0º ø270 350 x 240 260 x 260 45º (Right) ø230 230 x 150 210 x 210 45º(Left) ø200 200 x 140 170 x 170 60º(Right) ø140 140x140 140x140.