WEP 992DA+ ND soldering station is a 2-in-1 soldering station: - Hot air, used for desoldering and soldering electronic circuits such as BGA, SMD and etc. Blowing in the station is achieved by means of a fan. - More powerful grotto flask with a peak power of 72-75W (original Japanese-made Hakko heating element) and fume extractor WEP 992DA+ ND soldering station is suitable for soldering and desoldering electronic components like SOIC, CHIP, QFP, PLCC, BGA, SMD, tid (especially cell phones). The station is used for soldering and desoldering electronic components, shrinking, welding plastics, heating. The WEP 992DA+ ND soldering iron is a hot air soldering station and a soldering tip. The station is equipped with a PID microprocessor, which checks the station's operating parameters in 20ms cycles and corrects them to the set values. The values of temperature, airflow power, operating mode, are visible on a large easy-to-read LCD display, which greatly facilitates the work. The hotair soldering iron is equipped with a ceramic heating element, which heats up quickly and evenly. The heater is made of hard alloys, allowing long working time at high temperatures, while not deforming, this greatly increases the stability of the work and extends the life of the heater. There is a micro-contact in the hot air flask holder, which, when the flask is put down, causes the flask to go into standby mode, by cooling the heating element and then turning off the air supply. This extends the life of the heater and saves electricity. The station is equipped with functions for checking the correct operation we receive messages about a short circuit, overloading of circuits, failure to achieve the set temperature. All these errors are shown on the display. Choosing the automatic operation mode, when we put the hot flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service Features: - 3 Work Programs. The soldering station has the ability to store 3 work programs for hot air and flask. Depending on the type of work assembly, disassembly, set the appropriate program. - hot air operation in automatic/manual mode. Choosing the automatic operation mode, when you put the hot air flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. This will ensure long, trouble-free operation of the heating element, save electricity and ensure the safety of service. Choosing the manual mode, when we often need to solder something, then we save time and increase the efficiency of work. It is recommended to switch to automatic mode before finishing work. - temperature correction. It depends on the operating environment, the efficiency of the heating element, the power of the blowing, the consumption of the mainsail, all this affects the appropriate temperature correction to obtain the set parameter. - C/F operation. Possibility to set on the display in which units the temperature will be displayed. - Sleep function for the mains soldering iron. The soldering iron is equipped with a sleep mode, when the flask is not used, after a pre-set time from the range of 0-99min it goes into sleep mode, i.e. the flask is heated to a temperature of 200C, this prevents excessive oxidation of the tip, and this affects its life and the heating element. We have the option to disable the mode by setting 0. - a mainsail flask with a heating element that heats up quickly, maintains a stable temperature and is electrostatically safe. - fume extractor from under the mainsail flask - the smoke generated during the soldering process is immediately extracted providing the user with a healthier working environment Technical data: - voltage 220-240V - power consumption 720W - working environment from 0 to 50stC - compact design with easy-to-read LCD display. - PID controller - microprocessor control of parameters: temperature, blowing power, operating time, temperature correction - protection against reaching too high temperature and informing with an alarm. - possibility to save 3 working programs (temperature, blowing power) - Cooling function - F/C temperature display mode Included: - WEP 992DA+ ND soldering station - hotair flask stand - set of nozzles: - round nozzle with a diameter of 2.5mm - round nozzle with a diameter of 4.4mm - circular nozzle with a diameter of 6mm - round nozzle with a diameter of 9mm - square nozzle 12x12mm - arrowhead flask stand with cleaning sponge - 908B arrowhead flask with T-B blade with fume extractor - chip picker - power cord